E28 Shifter FAQ

E28 technical advice asked and given! Troubleshooting, modifications and more.
Brad D.
Beamter
Beamter
Posts: 10735
Joined: Feb 12, 2006 12:00 PM
Location: San Antonio, TX
Contact:

E28 Shifter FAQ

Post by Brad D. »

Since there are many questions regarding the shift components and how to remove slop from an e28 shifter, I thought I would throw together a quick FAQ with pictures, part numbers and importance of components. If anyone has anything else to add about shifters, short shifters or shifter parts, this is the place.

Aluminum Shift Console Parts

Image

Sheet Metal Console Parts

There are different sheet metal consoles and console mounting blocks. I believe I have now listed the various different parts.
Image

As we know most BMW shift levers will work in an e28, some better than others. Below is the diagram that has been posted all over the internet showing the difference in critical dimensions of some of the popular options.

Image

I also thought that Ron Stygar's site would be worth linking to.
Unofficial BMW Shift Lever Info Page

The following images were used from Ron's site.
Image
Image
Image
Image
Image
Image
Image
Last edited by Brad D. on Jan 11, 2010 7:44 AM, edited 2 times in total.
Coldswede
Posts: 6859
Joined: Oct 10, 2008 1:48 PM
Location: Back U.P. North,. Where the water's blue, the wind is free and seasons four.

Post by Coldswede »

:alright: :up: Thank you Brad
Scottinva
Posts: 3663
Joined: Dec 07, 2008 7:32 PM
Location: Norfolk, Virginia

Post by Scottinva »

I modified my shifter in a DIY way, by welding a good bit to below where the shift knob pivots, than lathed a bronze bushing which was put in with a press. It's way tighter than any e28 I have felt, even with a shift kit.
WVe28
Posts: 2125
Joined: Jul 29, 2007 8:57 AM
Location: Charleston, WV

Post by WVe28 »

You're the best, man! I'll be doing this in the next few months and this is great. My sheet metal console is still broken in half. You think you have slop! :rofl:
Mike W.
Posts: 26872
Joined: Feb 12, 2006 12:00 PM
Location: California Whine Country

Post by Mike W. »

Is that the G260/5 or the G265/6 sheet metal support? They're not the same. G265 eta and M30 aren't even the same.
Brad D.
Beamter
Beamter
Posts: 10735
Joined: Feb 12, 2006 12:00 PM
Location: San Antonio, TX
Contact:

Post by Brad D. »

Mike W. wrote:Is that the G260/5 or the G265/6 sheet metal support? They're not the same. G265 eta and M30 aren't even the same.
You are correct Mike. I'm going to make a couple of changes to clarify everything. I shouldn't have hastily posted it from work but I was bored.
tsmall07
Beamter
Beamter
Posts: 12774
Joined: May 22, 2006 4:32 PM
Location: Springfield, vA

Post by tsmall07 »

Big Bronze Rim wrote: You are correct Mike. I'm going to make a couple of changes to clarify everything. I shouldn't have hastily posted it from work but I was bored.
Image :rotz: :lol:
CSBolger
Posts: 3485
Joined: Nov 27, 2007 12:00 AM
Location: Palmdale, CA

Post by CSBolger »

Big Bronze Rim wrote:I shouldn't have hastily posted it from work but I was bored.
I wish my bored posts were full of awesome information! :oops:

Does anyone have the lengths of the E39 shifters? I have one out of a 530i, and I'm guessing it's around the same as the 1.9 Z3's.
Brad D.
Beamter
Beamter
Posts: 10735
Joined: Feb 12, 2006 12:00 PM
Location: San Antonio, TX
Contact:

Post by Brad D. »

I have added clarification to the sheet metal console info as well as added some of the information from Ron Stygar's excellent research on shift levers.
derrith
Posts: 2980
Joined: Sep 18, 2007 1:02 AM
Location: Bay Area, CA

Post by derrith »

Big Bronze Rim wrote:I have added clarification to the sheet metal console info as well as added some of the information from Ron Stygar's excellent research on shift levers.
I've found with my sheet metal consoles that if you use one of the rubber bushings that hold the airbox (part number 13711259818) instead of part number 15 (stop buffer) it is much easier to install and far less likely to fail than that silly little rubber piece. I've also used transmission mounts if I've had one lying around. They work well.
Brad D.
Beamter
Beamter
Posts: 10735
Joined: Feb 12, 2006 12:00 PM
Location: San Antonio, TX
Contact:

Post by Brad D. »

Excellent tip!
nnarth212
Posts: 1953
Joined: Aug 10, 2009 6:06 PM
Location: San Francisco

Post by nnarth212 »

Question:
on the aluminum console why are the yellow washers and circlips at either end of the select rod different sizes and part numbers (as shown by real oem) ? the color photo shown above calls them generically 'yellow washers, circlips' are they interchangeable or not?

I can't find part numbers for the pieces 14, and 16 at autohausaz.... irritating.

Thanks fellas

ALSO:


I have part (25 11 7 501 309) 13/9, guy that attaches to the trans select shaft for sale.

I have about 10 of them, If you need one let me know. Cheap.

What's fair-- $9?
johne
Posts: 117
Joined: Nov 06, 2008 9:58 PM
Location: Langhorne, Pa.

e28 shifter FAQ

Post by johne »

I have an e28 M5 with the 265 conversion. Which means it has the sheet metal console. I'm using the stock M5 shifter which is fairly tight but has a long throw especially to 2nd. Anyone know the ratio of that shifter so I can compare it to the others above?? Alternatively has anyone used any the shifters above with that console and if so which one and what were the results?? Thanks John
Brad D.
Beamter
Beamter
Posts: 10735
Joined: Feb 12, 2006 12:00 PM
Location: San Antonio, TX
Contact:

Post by Brad D. »

Any of the above shifters CAN be run with the sheet metal console. It requires a small modification of the upper shifter bushing but it is very easy. I've got a G265 w/sheetmetal console in my car and am using a Z4 3.0 shift lever and it works great. I think I have a stock shifter laying around that I can measure.
johne
Posts: 117
Joined: Nov 06, 2008 9:58 PM
Location: Langhorne, Pa.

e28 shifter faq

Post by johne »

Thanks. Based on the pictures above which/where is the "upper" shifter bushing??
Brad D.
Beamter
Beamter
Posts: 10735
Joined: Feb 12, 2006 12:00 PM
Location: San Antonio, TX
Contact:

Post by Brad D. »

I'm trying to remember if I had to cut one or both but it is 10 in the first sheetmetal pic and 19 in the second. They won't fit over the lever so you make one cut with a very sharp knife and the slip it on. You won't ever know it was cut once it's installed.
johne
Posts: 117
Joined: Nov 06, 2008 9:58 PM
Location: Langhorne, Pa.

e28 shifter faq

Post by johne »

Thanks I see it perfectly now. Sorry about the late reply my daughter is getting married next Friday and my house is nuts.
John
DJM1986-5
Posts: 1617
Joined: Sep 29, 2008 11:00 PM
Location: Greenville, SC

Post by DJM1986-5 »

I actually got the C clip out from between the upper and lower shifter pieces, pulled them apart and installed the upper bushing/cup without cutting. I'm cutting it the next time....An HO railroading saw is great for cutting that bushing. It's razor thin and incredibly sharp.

And yes the yellow O rings/bushings are all the same size. I have plenty of spares.
Brad D.
Beamter
Beamter
Posts: 10735
Joined: Feb 12, 2006 12:00 PM
Location: San Antonio, TX
Contact:

Post by Brad D. »

DJM1986-5 wrote:I actually got the C clip out from between the upper and lower shifter pieces, pulled them apart and installed the upper bushing/cup without cutting.
That will work for the stocker but the later non-stock shifters do not come apart making cutting a requirement.
derrith
Posts: 2980
Joined: Sep 18, 2007 1:02 AM
Location: Bay Area, CA

Post by derrith »

CSBolger wrote:
Big Bronze Rim wrote:I shouldn't have hastily posted it from work but I was bored.
I wish my bored posts were full of awesome information! :oops:

Does anyone have the lengths of the E39 shifters? I have one out of a 530i, and I'm guessing it's around the same as the 1.9 Z3's.
I know that then e39 m5 shifter is exactly the same as the ie short shifter and that the e39 530i is a different ratio to that, for the worse.
CSBolger
Posts: 3485
Joined: Nov 27, 2007 12:00 AM
Location: Palmdale, CA

Post by CSBolger »

derrith wrote:
CSBolger wrote:
Big Bronze Rim wrote:I shouldn't have hastily posted it from work but I was bored.
I wish my bored posts were full of awesome information! :oops:

Does anyone have the lengths of the E39 shifters? I have one out of a 530i, and I'm guessing it's around the same as the 1.9 Z3's.
I know that then e39 m5 shifter is exactly the same as the ie short shifter and that the e39 530i is a different ratio to that, for the worse.
Yup. According to Brad's post the ratios are identical. One thing I do like about it is that it's just a bit shorter than stock - hardly noticeable until you drive a stock E28. I'll be going with something else soon though.
Paul in N FL
Posts: 2069
Joined: Sep 30, 2008 10:32 PM
Location: Jax, FL

Post by Paul in N FL »

Sticky?
davintosh
Posts: 13944
Joined: Jan 28, 2009 1:05 AM
Location: Sioux Falls, SD
Contact:

Post by davintosh »

Paul in N FL wrote:Sticky?
x 2. Maybe add some info on the how-to of gaining access to the parts for rebuild/replacement. Could always start with some of the helpful hints I received to my dumb questions about the process of rebuilding the shift linkage.

http://www.mye28.com/viewtopic.php?t=59341
http://www.mye28.com/viewtopic.php?t=62489
http://www.mye28.com/viewtopic.php?t=69656

In short, it helps to get the driveshaft out of the way, but to do so you've got to loosen the center bearing, but to do so you've got to at least loosen the exhaust & catalytic converter.
Mike W.
Posts: 26872
Joined: Feb 12, 2006 12:00 PM
Location: California Whine Country

Post by Mike W. »

C'mon Beamters, sticky this thing!!!
BigMac
Posts: 675
Joined: Jan 16, 2010 2:03 PM
Location: Chandler, AZ
Contact:

Post by BigMac »

Is there a place to purchase all the items needed for the Z3 shifter upgrade?

Friend of mine mentioned that when he did it he called up Steve Haygood and he knew everything needed, but apparently he's no longer in business.
Post Reply